Bush Hog 3715 Manual del operador

OPERATIONll MAINTENANCE06/09 Rev.1$4.0050029874Model 3715/3710Flex-Wing Rotary CutterOperator’s ManualBUSH HOG®

2-2 OPTIONAL VALVE MOUNTING BRACKET INSTALLATION (Figure 2-2)A. Place bottom bracket at desired mounting loca-tion. Mark 2-4 holes (as needed) for

9Figure 2-3 Linkage Rod Jamnut Turnbuckle Additional mulching of cut material may be attained byoperating with the rear of the cutter slightly low

103-1 GENERAL SAFETYOnly qualified people should operate this machine.Operator should wear hard hat, safety glasses, andsafety shoes. It is reco

4-1 MAINTENANCE CHECK LISTPerform scheduled maintenance as outlined below.Lower machine to ground, turn off tractor and set park-ing brake before doin

7. Gearboxes - Add EP80W-90 oil, if necessary,to bring oil level to check plug located onside of housing. Capacity of transfergearbo

4-3 BLADE REPLACEMENTIt is not necessary to remove the complete bladeholder assembly to replace the blades.* Blade boltsare accessible throug

BUSH HOGMODEL3715/3710FLEX-WING ROTARY CUTTER14®(Model 3710 Illustrated)1” x 9-7/8”

1” x 8-5/8”1’ x 7-11/16”1” x 12-11/16”1” x 12-11/16”15

TABLE 4-1 GENERAL TROUBLESHOOTINGPROBLEM PROBABLE CAUSE REMEDYUneven cut Cutter not level side to side or front to rear. Refer to Section II.Worn or b

SECTION VASSEMBLYTHE FOLLOWING SAFETY PRECAUTIONS SHOULD BE THOROUGHLY UNDERSTOOD BEFORE ATTEMPTING MACHINE ASSEMBLY.1. Wear personal protective equip

CONGRATULATIONS!You have invested in the best implement of its type on the market today.The care you give your Bush Hog implement will greatly determi

Figure 5-2 Axle Cylinder Mounting HolesFront Of Cutter B. Pin axles onto wings and center deck using pivotpins and 3/8 x 2” bolts with locknuts. (Page

H. Connect height adjusting cylinder from cutterdeck to axle. Secure the cylinder to the axle using 5-1/8” pin with roll pin and cotter pin. (

P. Attach driveline retainer ring to the mountingbracket welded to the deck of each wing in front of thegearbox input shaft. Secure with two 1

IMPORTANTFAILURE TO RETIGHTEN NUTS TO ORIGI-NAL POSITION MAY CAUSE DAMAGE TOIMPLEMENT AND/OR TRACTOR DUE TO IMPROPER SLIP CLUTCH TORQ

Figure 5-21 Band Installation5-4 BAND INSTALLATIONA. Raise wings to the transport position and in-stall transport lock pins. Bands will b

23228”Hydraulic Hose228”Hydraulic Hose228”Hydraulic Hose3715 PLUMBING DIAGRAM(USING REMOTE VALVE)Center HeightControl CylinderBreatherPlug90° Elbow 3/

24BreatherPlug90° Elbow 3/4” SAE“O” Ring Boss to 9/16” JIC3710 PLUMBING DIAGRAM(USING REMOTE VALVE)Center HeightControl CylinderRight WingLift Cylinde

SAFETY DECALSTo promote safe operation, Bush Hog supplies safety decals on all products manufactured. Because damage canoccur to safety decals either

26500294187878678608

TORQUE SPECIFICATIONSProper toque for American fasteners used on Bush Hog equipment.Recommended Torque in Foot Pounds (Newton Meters).*Proper torque f

3715/3710 ROTARY CUTTERTABLE OF CONTENTSSECTION/PARA PAGEWarranty ...2Deal

28INSTALLATION OF SPECIAL LOCKING WASHER AND GRADE 5 BOLTSON THE MODEL 3715 / 3710 AXLE TURNBUCKLE.Refer to the illustrations below for proper locatio

2501 Griffin Ave., llSelma, AL 36703Telephone (334) 874-2700 ll www.bushhog.com

LIMITED WARRANTYOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOBush Hog warrants to the original purchaser of any new Bush Hog equipment, purchased from an au-thorize

DEALER PREPARATION CHECK LIST3715 / 3710 ROTARY CUTTERBEFORE DELIVERING MACHINE — The following check list should be completed.Use the Operator’s Manu

Safety Alert SymbolThis Safety Alert Symbol means: “ATTENTION! BECOME ALERT!YOUR SAFETY IS INVOLVED!”This symbol is used to call attention to safetypr

IMPORTANT SAFETY PRECAUTIONSThis symbol is used to call attention to safetyprecautions that should be followed by the op-erator to avoid accidents. Wh

IMPORTANT FEDERAL LAWS AND REGULATIONS* CONCERNINGEMPLOYERS, EMPLOYEES AND OPERATIONS.*(This section is intended to explain in broad terms the concept

1-1 INTRODUCTIONWe are pleased to have you as a Bush Hog customer. Your Model 3715/3710 Flex Wing RotaryCutter has been carefully designed t